How to Use Fluke MicroMapper Pro?

How to Use Fluke MicroMapper Pro?
By Colin Yao

What Can the MicroMapper Help You Do?

Fluke's MicroMapper is a hand-held cable tester to facilitate enables arrangement professionals to quickly and without doubt verify the integrity of Ethernet twisted twosome cables.

During individual step, the MicroMapper can test twisted twosome cabling on behalf of opens, shorts, reversed, crossed, and split pairs.

You need to slide the switch to the "Cable" arrangement, press the "TEST" button and the MicroMapper will in that case robotically check on behalf of one existing faults in your cable.

You can management the remote item on behalf of one-person taxing of installed cabling. It moreover has a tone generator function which can be used with the MicroProbe cable tracer to follow cables and locate cables hidden in ceilings, walls, floors, and bundles.

Here is the chubby record of come again? The MicroMapper can help you see to.


1. Tests on behalf of wiring faults and detects opens, shorts, crossed, reversed, and split pairs. (Split twosome fault detection requires a smallest cable part of 15.75" (40cm))
2. Verifies protect integrity

3. MicroMapper's Remote Identifier enables individual person to test installed cabling

4. Easy to read fault ceremony and sky-scraping swiftness taxing

5. Generation of two tones on behalf of tracing cables and locating hidden cables

6. Debug-mode on behalf of detailed fault identification results

7. Auto-sleep mode to decrease power consumption



>> What Are on the MicroMapper Unit?

The Fluke MicroMapper has a very well designed user interface on behalf of cool undertaking. You can management the sequence of LED light to verify your taxing effect.


1. Pair and Shield indicator LEDs
2. Toner LED

3. "TEST" button

4. REMOTE Adapter with RJ45 jack

5. RJ45 jack on behalf of the central item

6. Off/Cable/Toner Switch

7. Fault LEDs

8. Low Battery LED



>> How to Use Fluke MicroMapper?

1. How to Use MicroMapper's Toner Operation


A) Slide the switch on the acceptably edge of MicroMapper to the "Toner" arrangement
B) Connect the cable to the MicroMapper's RJ45 jack. (To propel a tone into a piece of land panel, join individual top of the built-in piece of land cord to the MicroMapper's RJ45 jack and the other top to a jack on the panel.)

C) To generate tone 1, press and quickly emit the "TEST" button.

D) To generate tone 2, press and possess the "TEST" button on behalf of two seconds.

E) Use the MicroProbe to follow the connected cable. The show reception is strongest nearing the cable under test.

F) Slide the switch on the acceptably edge to the "OFF" arrangement to discontinue the tone. (Always power the item rotten to prevent battery drain.)



2. How to Use MicroMapper Test


A) Slide the switch on the acceptably edge to the "Cable" arrangement to break MicroMapper on.
B) Connect individual top of the cable to be tested on the MicroMapper's RJ45 jack.

C) Connect the other top of the cable to the MicroMapper Remote's RJ45 jack.

D) Press the "TEST" button to stance the results.

E) The horizontal LEDs indicate the cable's integrity status.

Green: Pair or Shield is good quality

Green Flashing: Pair or Shield is faulty

No Light: Pair is honest or cable is not shielded

The vertical LEDs indicate the wiring faults and a low battery status. Wiring faults are: SHORT, REVERSED, MISWIRE, SPLIT PAIRS.

F) To realize off a fault on a detail twosome, management MicroMapper's diagnostic characteristic

G) Press and possess "TEST" button on behalf of more than 2 seconds.

MicroMapper will check each one twosome and the protect pausing and flashing each one emerald LED disjointedly. If a faulty twosome is detected, the corresponding fault status will blink in red.

Colin Yao is the sales boss on Fiber Optics For Sale Co.

Fiber Optics For Sale Co. Is a chubby line stocking distributor of Fluke Networks MicroMapper Pro and Fluke MT-8200-49A MicroMapper. Find even more products on FO4SALE.Com.